Wi-Fi Problemen met Bootloader 4.6 ?

[ArB]

Ook deze is wel handig
bron


No Wi-Fi or Signal?
Follow this guide to re-flash your phone with the baseband that came with 1.1.2, then use DFU restore to 1.1.4. This will give you a clean baseband for 1.1.4 and get rid of those pesky Wi-Fi and signal problems.
NOTE: You will lose Wi-Fi during this process, so Install Term-VT100 app on your phone with Installer or iBrickr so you can perform these commands from the phone itself.
1. Make sure Auto-Lock is set to Never by going to Settings -> General -> About
2. Download the BB tools package for 4.6 with the bbupdater flasher and the required baseband files. This includes a special version of ieraser for 1.1.2 called ienew.
3. Upload the files (bbupdater, ienew, secpack, ICE04.02.13_G.eep, ICE04.02.13_G.fls) to the iPhone via SFTP or SCP to /usr/bin
4. SSH into the iPhone and make bbupdater and ienew executable,
chmod +x bbupdater and chmod +x ienew
5. Disable the CommCenter with the command:
launchctl unload /System/Library/LaunchDaemons/com.apple.CommCenter.plist
6. Open Term-VT100 on the phone and go to /usr/bin
7. Erase the baseband with ienew, the new version of ieraser
./ienew
8. Flash the 4.02.13 baseband onto the phone
./bbupdater -f ICE04.02.13_G.fls -e ICE04.02.13_G.eep
9. After 3 minutes the baseband is programmed. Check by typing
./bbupdater -v
Verify that the output has the new baseband firmware version as shown below
firmware: DEV_ICE_MODEM_04.02.13_G
eep Version: EEP_VERSION: 208
eep revision: EEP_REVISION: 1
bootloader: BOOTLOADER_VERSION: 4.6_M3S2
10. Put phone in DFU and run iPlus to unlock
11. After running iPlus, you can check your baseband and bootloader with BB Info. See Determining your Bootloader with BB Info, from Installer in the Guides. For phones that had 4.6BL, the bootloader will now show 3.9 for the 3.9 Fake Blank Bootloader.

__________________
Origineel: iPhone US 1.0.2 OTB BL3.9 | Huidige firmware: 3.X | Bootloader: 3.9 | Baseband: 04.05.04_G

Zoek in de WIKI voor 99% van alle antwoorden.
Op persoonlijke berichten met vragen over de iPhone reageer ik niet. Gebruik hiervoor het forum. Ik ben geen helpdesk.

[croiman]

zeer leuk, ook handig voor degene die trug na 112 state wilt gaan MET de baseband.

__________________
PM functie overhit. Gelieve alleen serieuze probleem gevallen via PM.
Going from iphone extreme mod to Motorola Photon Q 4G LTE with simcard mod and lots more.

[jeremy14]

Oorspronkelijk geplaatst door ArB

Ook deze is wel handig
bron


No Wi-Fi or Signal?
Follow this guide to re-flash your phone with the baseband that came with 1.1.2, then use DFU restore to 1.1.4. This will give you a clean baseband for 1.1.4 and get rid of those pesky Wi-Fi and signal problems.
NOTE: You will lose Wi-Fi during this process, so Install Term-VT100 app on your phone with Installer or iBrickr so you can perform these commands from the phone itself.
1. Make sure Auto-Lock is set to Never by going to Settings -> General -> About
2. Download the BB tools package for 4.6 with the bbupdater flasher and the required baseband files. This includes a special version of ieraser for 1.1.2 called ienew.
3. Upload the files (bbupdater, ienew, secpack, ICE04.02.13_G.eep, ICE04.02.13_G.fls) to the iPhone via SFTP or SCP to /usr/bin
4. SSH into the iPhone and make bbupdater and ienew executable,
chmod +x bbupdater and chmod +x ienew
5. Disable the CommCenter with the command:
launchctl unload /System/Library/LaunchDaemons/com.apple.CommCenter.plist
6. Open Term-VT100 on the phone and go to /usr/bin
7. Erase the baseband with ienew, the new version of ieraser
./ienew
8. Flash the 4.02.13 baseband onto the phone
./bbupdater -f ICE04.02.13_G.fls -e ICE04.02.13_G.eep
9. After 3 minutes the baseband is programmed. Check by typing
./bbupdater -v
Verify that the output has the new baseband firmware version as shown below
firmware: DEV_ICE_MODEM_04.02.13_G
eep Version: EEP_VERSION: 208
eep revision: EEP_REVISION: 1
bootloader: BOOTLOADER_VERSION: 4.6_M3S2
10. Put phone in DFU and run iPlus to unlock
11. After running iPlus, you can check your baseband and bootloader with BB Info. See Determining your Bootloader with BB Info, from Installer in the Guides. For phones that had 4.6BL, the bootloader will now show 3.9 for the 3.9 Fake Blank Bootloader.

Deze lnik werkt niet meer?? kan iemand mij het ischien toesturen???

Alvast bedankt

__________________
iPod Touch 4G 32GB White | Live each day as it would be your last